RepairHub

What Is Microsoldering, and When Does a Device Need Board Repair?

By Ruslan Hryhorenko, repair technician at RepairHub

Updated

“The motherboard is bad, you need a new one.” Many people hear that about a phone, a MacBook or a console and assume the device is finished. Sometimes it is. Often, though, the board has one failed part the size of a grain of rice, and that part can be replaced. Doing that is called microsoldering, or board level repair. This guide explains what it is and how to tell when your device might need it.

What Is Microsoldering? When a Device Needs Board Repair
In this guide 6 sections

What microsoldering is

Every phone, tablet, laptop and console has a main board, also called the motherboard or logic board. It holds the processor, the memory, the storage, and hundreds of tiny components: capacitors, resistors, filters, chips that manage charging, power and video. Many of these parts are smaller than the tip of a pencil.

Ordinary repairs swap whole modules. A new screen, a new battery, a new charging flex cable. Microsoldering goes one level deeper. A technician works under a microscope with a fine soldering iron and hot air to remove one failed component from the board and solder in a new one, or to rebuild a damaged connection.

It takes training and the right equipment: a stereo microscope, a temperature controlled station, a bench power supply that shows how much current the board draws, and a lot of patience.

Problems that usually need board work

Charging ports soldered to the board. On many iPads, game consoles and laptops, the charging port is not on a separate cable. It sits on the main board. When it wears out or breaks, the old port has to be desoldered and a new one soldered on. See our iPad not charging page for an example.

HDMI ports on consoles. The PS5 and Xbox HDMI ports are soldered to the board and break when a cable is yanked or the console is moved while plugged in. Replacing them is classic microsoldering work. Our PS5 HDMI port and Xbox HDMI port pages explain the repair.

Charging chips. If a phone, tablet or Switch does not charge even with a new cable, a new charger and a clean port, the chip that controls charging may have failed. Cheap chargers and power surges are common causes.

Liquid damage. Water and other liquids corrode the board and short out small parts. After cleaning, the corroded components often have to be replaced one by one.

Data recovery. When a phone will not turn on and the photos were never backed up, the data is still on the board. Bringing the board back to life long enough to copy the data is board level work. More on that in our guide on getting data off a dead phone.

Damaged connectors. The small sockets that the screen, battery and cameras plug into can crack or lose pins. They can be replaced on the board without replacing the whole board.

Rather have us fix it?

Free diagnostic, walk-ins welcome at 6201 Greenback Ln Suite A, Citrus Heights.

Signs your device may have a board problem

You cannot see board damage without opening the device, but some symptoms point to it:

  • it is completely dead even after a long charge with a known good charger
  • it gets hot while it is off or charging, or the charger gets hot
  • it charges only with one specific charger, or charges very slowly no matter what
  • there is no picture on the TV although the console turns on and the cable is fine
  • the device died right after a drop, a spill or a power surge
  • a new battery or a new screen did not fix the problem

None of these prove a board fault. A dead battery or a bad cable can look the same. That is why the first step is always a diagnostic.

Why it matters to you

A new main board, when one is available at all, can cost close to what the device is worth. A new board also means your data is gone, because on modern phones and Macs the storage is part of the board. Repairing the original board keeps your data and is often the cheaper way back to a working device.

It is not magic, though. Some boards are too badly burned, cracked or corroded to save. An honest shop will tell you that after looking, before you pay for a repair that cannot work.

What you should not try at home

Videos make board work look simple. On a real board the components are tiny and packed together. Too much heat lifts the pads that parts sit on. A slip of a screwdriver can knock off neighboring parts. Every one of those mistakes makes a professional repair harder or impossible. If you think the problem is on the board, power the device off and leave it as it is.

Board repair in Citrus Heights

RepairHub at 6201 Greenback Ln Suite A in Citrus Heights does board level work, including motherboard and microsoldering repairs on phones, tablets, laptops and consoles. The diagnostic is free and walk-ins are welcome. Tell us what happened right before the device stopped working, because a drop, a spill or a new charger is a useful clue.

You can see the devices we work on in our repair section, including PlayStation and iPad. For an estimate on one of the most common board jobs, open the repair calculator with PS5 HDMI port selected, or pick your own device there.

Bring it to our Citrus Heights shop

  • Free diagnostic and estimate
  • Walk-ins welcome, no appointment needed
  • Screen replacements are done in 15 minutes
  • Microsoldering jobs are done the same day

6201 Greenback Ln Suite A, Citrus Heights, CA 95621

Get directions

+1 916-595-7120

Monday - Friday
10:00 am - 06:00 pm
Saturday
10:00 am - 2:00 pm
Sunday
Closed

Rather have us fix it?

Free diagnostic, walk-ins welcome. See the price for your repair first.

Let's talk about your repair

Or call +1 916-595-7120