RepairHub

Apple Watch Won't Pair With Your iPhone: What to Try

By Oleh Hryhorenko, repair technician at RepairHub

Updated

You bought a new iPhone, reset your watch, or the watch just stopped showing notifications, and now it will not pair again. The spinning animation never finishes, or the iPhone says it cannot connect. People search for this as “how to repair Apple Watch to phone”, and the fix is almost always on the software side. Hardware is the exception, but it does happen, so we cover both.

Work through the steps below in order. Each one takes a few minutes.

Apple Watch Won't Pair With Your iPhone? How to Fix It
In this guide 6 sections

First, check whether the watch is really disconnected

Swipe up (or press the side button on newer watchOS versions) to open Control Center on the watch. A red iPhone icon or a red X means the watch has lost its link to the phone. A green iPhone icon means it is connected and the problem is somewhere else, usually notification settings.

If the watch shows as disconnected:

  1. On the iPhone, open Control Center and make sure Bluetooth and Wi-Fi are both on. Turning them off from Settings and back on is more reliable than tapping the Control Center buttons.
  2. Turn off Airplane Mode on both the iPhone and the watch.
  3. Keep the two devices next to each other.
  4. Restart both. On the watch, hold the side button, tap the power icon and slide to turn it off. Then turn the iPhone off and on.

A lot of lost connections come back after a simple restart of both devices.

Make sure the software versions match

Each watchOS version needs a recent enough iOS on the iPhone. A watch that was updated on one phone may refuse to pair with an older phone that runs an older iOS. The reverse also happens: an old watch may not pair with a brand new iPhone until the watch is updated.

  • On the iPhone, go to Settings, General, Software Update and install anything that is waiting.
  • If the iPhone is fully updated and the watch still will not pair, the watch model may simply be too old for that iPhone. Apple lists which watches work with which iOS versions on its support site.

Rather have us fix it?

Free diagnostic, walk-ins welcome at 6201 Greenback Ln Suite A, Citrus Heights.

Unpair and pair again

If the watch connected before and now will not, a clean unpair and pair usually solves it.

  1. Open the Watch app on the iPhone and tap All Watches at the top.
  2. Tap the info button next to your watch, then Unpair Apple Watch. The iPhone saves a backup of the watch before it unpairs.
  3. When the watch shows the language screen, hold it near the iPhone. The pairing card should pop up on the phone.
  4. If the animation does not appear, tap the info icon on the watch and choose Pair Manually, then follow the prompts.
  5. When asked, restore from the backup the iPhone just made.

Keep the watch on its charger during pairing. Setup can take a while, and a watch that dies halfway through has to start over.

When the watch is stuck or asks for a password

The watch is frozen. Force restart it by holding the side button and the Digital Crown together for at least ten seconds, until the Apple logo appears.

You cannot unpair from the iPhone. You can erase the watch on its own. On the watch, open Settings, General, Reset and choose Erase All Content and Settings. Then pair it again as new or from a backup.

The watch asks for an Apple Account password. That is Activation Lock. It protects the watch if it is lost or stolen. Only the owner’s Apple Account password removes it. If you bought the watch used, the seller has to remove it from their account. No repair shop can bypass Activation Lock, and you should be wary of anyone who says they can.

Signs it is a hardware problem

Software steps fix most pairing problems. These signs point to the watch itself:

  • The screen does not respond to touch. You cannot tap through the pairing steps if the touch layer is dead. This is common after a crack, even a small one at the edge. Our Apple Watch screen repair page covers it.
  • The watch dies within minutes or will not charge. A worn battery can shut the watch down during setup. A swollen battery can also push the screen up from the case, which is a reason to stop charging it and bring it in. See Apple Watch battery replacement.
  • It stopped pairing right after water or a hard hit. Water resistance wears down over time, and the seals do not survive a crack in the screen. Liquid inside can damage the board and the wireless parts.
  • It pairs, then drops the connection again and again even after an erase, an update and a new pairing. That pattern is worth a diagnostic.

Getting your Apple Watch checked in Citrus Heights

If you have restarted both devices, updated the iPhone, erased the watch and it still will not pair, bring it in. RepairHub is at 6201 Greenback Ln Suite A in Citrus Heights. The diagnostic is free and walk-ins are welcome. Bring the watch, its charger and the iPhone you want to pair it with, and know your Apple Account password in case the watch asks for it.

You can read more on our Apple Watch repair page. To see the options for your watch, open the repair calculator with Apple Watch selected.

Bring it to our Citrus Heights shop

  • Free diagnostic and estimate
  • Walk-ins welcome, no appointment needed
  • Screen replacements are done in 15 minutes
  • Microsoldering jobs are done the same day

6201 Greenback Ln Suite A, Citrus Heights, CA 95621

Get directions

+1 916-595-7120

Monday - Friday
10:00 am - 06:00 pm
Saturday
10:00 am - 2:00 pm
Sunday
Closed

Rather have us fix it?

Free diagnostic, walk-ins welcome. See the price for your repair first.

Let's talk about your repair

Or call +1 916-595-7120